Bicycle brakes

Bicycles use rim brakes, which grip the wheel rim, or disc brakes, which grip a rotor at the hub. Disc brakes work better in the wet; rim brakes are lighter and simpler. A bicycle on the road must have a working brake on each wheel.

Levers are tested before every ride, worn pads are replaced, and oil is kept off rims and rotors.

Brakes are the most important safety components on a bicycle. Two kinds are in general use: rim brakes, which grip the wheel rim, and disc brakes, which grip a steel rotor at the hub. Each works well when correctly adjusted, and each needs regular attention.

The law and the levers

A bicycle used on the road in the United Kingdom must have two independent braking systems, one acting on each wheel. By British convention the right-hand lever works the front brake and the left-hand lever the rear; bicycles bought abroad are often the other way round. A fixed-wheel bicycle counts as having a rear brake, and still requires a front one.

Rim brakes

  • Caliper brakes, on road bicycles: a single mechanism above the wheel squeezes two pads against the rim.
  • V-brakes, on hybrids and older mountain bikes: two long arms give strong leverage.
  • Cantilever brakes, on touring and older cyclo-cross bicycles.

Rim brakes are light, simple and easy to inspect and repair anywhere. They lose power in the wet, wear the rim itself over the years, and are affected by a buckled wheel.

Disc brakes

A caliper fixed to the frame or fork squeezes pads against a rotor bolted to the hub.

  • Mechanical disc brakes are worked by a cable. They are simple to maintain, and need adjusting as the pads wear.
  • Hydraulic disc brakes are worked by fluid in a sealed hose. They are more powerful, need a lighter touch and adjust themselves for wear, but servicing requires bleeding the system of air.

Disc brakes stop consistently in rain and mud, do not wear the rim and allow wider tyres. They are heavier, and the rotors are easily contaminated by oil. They are standard on mountain, gravel and most new hybrid and road bicycles.

Rotors and pads

  • Rotors range from 140 to over 200 millimetres across. Larger rotors give more power and shed heat better, and are fitted to mountain and electric bicycles.
  • Resin, or organic, pads are quiet and bite at once, but wear quickly in wet, gritty conditions.
  • Sintered, or metallic, pads last longer and cope with heat and mud, but are noisier and take longer to warm up.
  • Pads must be of the pattern made for the particular caliper.

Other types

  • Hub brakes, drum or roller, are enclosed and need little maintenance; they are found on town bicycles.
  • Coaster brakes, worked by pedalling backwards, are fitted to some children's and town bicycles.

Braking technique

  • The front brake supplies most of the stopping power, since weight shifts forward. Both brakes are applied together, progressively.
  • Braking is done before a bend, not in it.
  • In the wet, on gravel, leaves, painted lines and metal covers, braking is earlier and gentler.
  • On long descents, the brakes are applied firmly and released in turn, not dragged continuously.
  • The body moves back and low for a hard stop.

Checks before a ride

  1. Each lever is squeezed. It stops firmly before reaching the handlebar.
  2. The bicycle is pushed forward with each brake applied in turn. The wheel locks.
  3. Pads are looked at for wear, and cables for fraying.
  4. Wheels are spun to see that nothing rubs.

Maintenance

  • Rim brake pads are replaced when the grooves have worn away. They meet the rim squarely, clear of the tyre.
  • Disc pads are replaced when about a millimetre of material remains.
  • Rims and rotors are cleaned with a suitable cleaner or isopropyl alcohol and a clean cloth. Oil, spray lubricant and greasy fingers are kept away from rotors and pads; contaminated pads squeal, grip poorly and usually have to be replaced.
  • New disc pads are bedded in by a series of firm stops from moderate speed before they are relied on.
  • Cables are replaced when frayed, stiff or rusty.
  • A spongy hydraulic lever means air in the system, which is bled, with the fluid specified by the maker.
  • A rim worn concave, or past its wear indicator, is replaced before it fails.
  • With the wheel out, the lever of a hydraulic brake is not squeezed, since the pads close together.

Common faults

  • Squealing: contamination, glazed pads or misalignment.
  • Rubbing: a bent rotor, a buckled wheel or a caliper off centre.
  • A lever that pulls to the bar: worn pads, a stretched cable or air in the hose.
  • Juddering: a loose headset or caliper bolts.

Brakes are not a place for guesswork. A bicycle shop will service them, and an annual service is sensible for a bicycle in regular use. Other points to consider when buying are covered under choosing a bicycle.

Changed